7430A REV B Norge Dryer Parts List

Upper crisper drawer cover - glass not included

This cover holds up the top crisper drawer, and has drawer glides molded in it. This upper crisper drawer cover is a manufacturer-approved replacement part for your refrigerator. It has drawer glides molded into the frame but this part does not include the glass cover. To replace this part, lift out the glass cover and snap out the drawer frame. Snap this new frame cover into place and replace the glass.

Replacement ice maker

This 8-cube ice maker is used to help produce ice for your refrigerator. The ice maker receives water from the water inlet valve and will freeze the water until ice cubes are formed. Once the water has been frozen the ice cubes will be ejected from the mold into the ice bucket and will refill with water to repeat the process until the ice bucket is full. This ice maker does not include the bail or shut off arm. You can reuse the arms for your old ice maker or you can also order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. The harness can be reused. This ice maker will not fit refrigerators that have the ice auger mounted on the door. If your ice maker is not making ice you may need to replace this part. Please remember to disconnect the power and water supply before starting your repair. This ice maker is a genuine OEM part.

Refrigerator ice and water filter (filter canister)

Bake element - 220v 2300w (oven bake heating element with screw-on terminals. The element is 18-1/4 inches wide, 14-1/2 inches deep to mounting flange. Terminal ends extend 2-1/)

This closed-hinged style bottom bake element is located on the bottom of the oven cavity to supply the heat for baking. This bake element has screw-on wire terminals is 18 1/4-inch wide and 14 1/2-inch deep to mounting flange and the terminal ends extend 2 1/2-inch past the flange. The element is 2300 watts and 20 volts. If your oven is not heating evenly, the element will not heat, or there is little to no heat when baking, you may need to replace the element. This is a genuine OEM bake element. Please remember to disconnect the power to your oven before you start your repair.

Drive belt (belt drive)

This dryer drum drive belt is 89.5" long and has four ribs. This part helps spin the drum during the drying cycle.

Dishwasher upper rack adjuster (adjuster arm)

Door catch kit (use wpl 279570)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Suspension spring

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be off balance and noisy. Check your model to see how many springs are required for your model. The spring is sold individually.

Lower spray arm (lower spray arm with shields)

Upper roller and axle - kit of 4 (roller and stud asm (4pk))

The upper roller and axle attach to the upper rack to allow the dishrack to move in and out along the track of the dishwasher. This is a kit includes 4 rollers and 4 axles for your upper rack. If your dish rack is not moving in and out of the dishwasher properly you may have a broken or missing wheel and it will need to be replaced. The rollers and axles are made out of plastic and are white in color. This is a genuine OEM kit.

Dryer drum support roller (support)

This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the drum roller only and does not include the tri-rings. This part is sold separately. Most dryers require two drum rollers. It is recommended to check and replace both drum support rollers at the same time to ensure proper drum rotation and because they often wear at the same rate. The drum support roller holds the drum in the proper position while it spins on the support wheels. If rollers are worn out, they will cause the dryer to be noisy.

Lower front dishrack wheel (front roller & stud)

This wheel is located on the front lower rack. It includes the axle. Sold individually.

Duct felt seal (felt)

The duct felt seal allows the front of the drum to glide smoothly on the exterior panel while the drum is rotating. The seal is located between the back of the drum and the rear dryer panel. If the heat is escaping from the drum area causing the dryer to run too long or if there are marks on your clothes you many need to replace the duct felt seal. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Flat style oven igniter kit (sub 12400035)

The flat style gas oven igniter is used to ignite the gas to light the oven burner, which produces heat for your range. If the element has shorted out, is no longer glowing, or is glowing but only orange or red rather than white, then you will need to replace the oven igniter. When replacing the igniter please be very careful not to touch the gray element part of the igniter as it is very fragile. The igniter measures approximately 3-3/4"in length and the amperage range is 3.3 to 3.6. This igniter kit can replace igniters for either the broil or bake burners and can replace shorter and longer igniters. The kit includes the igniter, 4 wire nuts, insulation, 2 wire assembly and a bracket. This is a genuine OEM part. Please make sure to disconnect the power and shut off the gas supply before starting your repair.

Drawer slide rail - right side (slide asm rh)

This replacement drawer slide rail is for the right-hand side of your refrigerator. This part attaches to the inside wall of your refrigerator to support the sliding crisper drawer. If the rail is broken or the drawer is not sliding properly, you will need to replace the slide rail. You will need a Phillips screwdriver to complete this repair.